Perforated Metal Sheets
Precision-punched stainless steel, aluminum, galvanized and carbon steel sheets for facades, machine guarding, acoustic panels and filtration, with open area calculated for every pattern.
Perforated metal, punched on CNC perforating lines
MAISHI punches perforated sheets on CNC perforating lines and turret presses in round, square, slotted, hexagonal and decorative patterns. Every pattern is listed with hole size, pitch and calculated open area, so engineers can specify airflow, filtration and weight with confidence. Sheets are supplied flat in mill finish, sheared to size, rolled or bent, with plain margins for framing or welding.
Choose the hole shape for the job

Round hole
The most widely used pattern, with the largest choice of diameters and the best balance of strength and open area.

Square hole
Higher open area than round holes at the same pitch, with a clean, modern look for facades and fences.

Slotted hole
Directional openings for drainage, drying, grading and ventilation, and linear facade effects.

Hexagonal hole
The highest open area of any punched pattern, up to about 80%, for maximum airflow and sound transmission.

Straight-row round
Aligned holes for ceilings, furniture and signage where a grid look is preferred.

Decorative patterns
Cross, clover, diamond and custom shapes for interiors, retail fixtures and furniture. Micro perforation for acoustic ceilings.
Round hole, 60 degree staggered
Open area = 90.69 x d² / p². Other sizes and pitches can be tooled on request.
| Code | Hole (mm) | Pitch (mm) | Open area | Thickness (mm) |
|---|---|---|---|---|
| R0.8T2 | 0.8 | 2 | 14.5% | 0.5 – 0.8 |
| R1T2 | 1 | 2 | 22.7% | 0.5 – 1.0 |
| R1.5T3 | 1.5 | 3 | 22.7% | 0.5 – 1.5 |
| R2T3 | 2 | 3 | 40.3% | 0.5 – 2.0 |
| R2T3.5 | 2 | 3.5 | 29.6% | 0.5 – 2.0 |
| R3T5 | 3 | 5 | 32.6% | 0.8 – 3.0 |
| R4T6 | 4 | 6 | 40.3% | 1.0 – 4.0 |
| R5T8 | 5 | 8 | 35.4% | 1.0 – 5.0 |
| R6T9 | 6 | 9 | 40.3% | 1.0 – 6.0 |
| R8T11 | 8 | 11 | 48.0% | 1.0 – 6.0 |
| R10T13 | 10 | 13 | 53.7% | 1.5 – 6.0 |
| R10T15 | 10 | 15 | 40.3% | 1.5 – 6.0 |
| R20T27 | 20 | 27 | 49.8% | 2.0 – 6.0 |
Hexagonal hole patterns
| Across flats (mm) | Pitch (mm) | Open area | Thickness (mm) |
|---|---|---|---|
| 2 | 2.5 | 64% | 0.5 – 1.0 |
| 4.5 | 5 | 81% | 0.5 – 1.5 |
| 5 | 6 | 69% | 0.5 – 2.0 |
| 6 | 8 | 56% | 0.8 – 2.0 |
| 10 | 12 | 69% | 0.8 – 1.5 |
| 12 | 15 | 64% | 1.0 – 3.0 |
| 15 | 18 | 69% | 1.0 – 3.0 |
| 17 | 22 | 60% | 1.0 – 3.0 |
Metals and mill finish condition
| Material | Grades | Mill finish condition |
|---|---|---|
| Aluminum | 1060, 3003, 5005, 5052 | Mill finish; usually coated or anodized for outdoor use |
| Stainless steel | 304, 316L | 2B or No.4 brushed; can be installed outdoors as supplied |
| Galvanized steel | DX51D / SGCC | Zinc coated; can be installed outdoors as supplied |
| Carbon steel | SPCC, Q235 | Oiled; must be coated before outdoor use |
| Corten steel | Corten A / Q355NH | Bare; develops its own rust patina |
| Titanium | Gr.1, Gr.2 | Bare |
| Brass, copper | H62, T2 | Bare, 0.5 – 3 mm |
Standard sheet sizes: 1000 x 2000, 1220 x 2440 (4 x 8 ft), 1250 x 2500 and 1500 x 3000 mm. Cut-to-length sheets up to 1500 x 4000 mm from coil.
Ten details for an accurate quotation
Perforated metal questions
What is open area?
The percentage of the sheet surface taken up by holes. A 5 mm round hole on 8 mm staggered centers gives about 35% open area.
What is the smallest hole you can punch?
As a rule, the hole diameter should be at least equal to the sheet thickness for carbon steel and aluminum, and 1.5 to 2 times the thickness for stainless steel. Smaller holes can be laser cut.
Which material is most corrosion resistant?
Stainless steel 316L and titanium, followed by 304 stainless steel, aluminum and galvanized steel.
Can you leave unperforated margins?
Yes. Side margins, end margins and blank areas can be specified on your drawing.
What is your minimum order and lead time?
10 sheets per size or pattern. Mill finish sheets ship in 15-20 days after order confirmation; coated sheets add 15 days.
Need a pattern that is not listed?
Send the hole size, pitch, material and thickness. We confirm tooling and open area in the quotation.